Air Conditioning



Central Air Conditioning Definitions

Air Conditioner: Assembly of equipment for the simultaneous control of air temperature, relative humidity, purity, and motion.

Air Cooled: Uses a fan to discharge heat from the condenser coil to the outdoors.

Air-Source: Air is being used as the heat source or heat sink for a heat pump.

BTU: British Thermal Unit. The amount of energy needed to change the temperature of one pound of water by one degree Fahrenheit. In practical terms, it represents a unit of measure of heat extracted from your home for cooling.

Central Air Conditioner System: System in which air is treated at a central location and carried to and from the rooms by one or more fans and a system of ducts.

Compressor: The pump that moves the refrigerant from the indoor evaporator to the outdoor condenser and back to the evaporator again. The compressor is often called "the heart of the system" because it circulates the refrigerant through the loop.

Condenser Coil: A series or network of tubes filled with refrigerant, normally located outside the home, that removes heat from the hot, gaseous refrigerant so that the refrigerant becomes liquid again.

Cooling Capacity: A measure of the ability of a unit to remove heat from an enclosed space.

COP: Coefficient of Performance of a heat pump means the ratio of the rate of useful heat output delivered by the complete heat pump unit (exclusive of supplementary heating) to the corresponding rate of energy input, in consistent units and under operating conditions.

EER: Energy Efficiency Ratio means the ratio of the cooling capacity of the air conditioner in British Thermal Units per hour, to the total electrical input in watts under ARI-specified test conditions.

Evaporator Coil: A series or network of tubes filled with refrigerant located inside the home that take heat and moisture out of indoor air as liquid refrigerant evaporates.

Free Delivery: There are no ducts and the unit may be installed in the field without ducts if needed.

Ground-Source: The ground or soil below the frost line is being used as the heat source or heat sink for a heat pump.

Ground Water-Source: Water from an underground well is being used as the heat source or heat sink for a heat pump.

Heat Pump: An air conditioner capable of heating by refrigeration. It may or may not include a capability for cooling. Outside air or water is used as a heat source or heat sink, depending upon whether the system is heating or cooling.

Heating Capacity: A measure of the ability of a unit to add heat to an enclosed space.

HSPF: Heating Seasonal Performance Factor means the total heating output of a heat pump in British Thermal Units during its normal usage period for heating divided by the total electrical energy input in watt-hours during the same period.

SEER: Seasonal Energy Efficiency Ratio means the total cooling output of a central air conditioner in British thermal units during its normal usage period for cooling divided by the total electrical energy input in watt-hours during the same period as determined using the ARI-specified test procedure. This rating is only for units with cooling capacity less than 65,000 BTU/hr. The higher the SEER, the more efficient the unit. The more efficient the unit, the lower the operating cost.

Single Package: A central air conditioner which combines both condenser and air handling capabilities in a single packaged unit.

Split System: A central air conditioner consisting of two or more major components. The system usually consists of a compressor-containing unit and condenser, installed outside the building and a non-compressor -containing air handling unit installed within the building. This is the most common type of system installed in a home.

Ton: The unit of measurement for air conditioning system capacity. One ton of air conditioning removes 12,000 BTUs of heat energy per hour from a home. Central air conditioners are sized in tons. Residential units usually range from 1 to 5 tons.

Water-Source: Water is being used as the heat source or heat sink for a heat pump. Sources of underground water are wells and sources of surface water are lakes, large ponds, and rivers.

Year-Round: Air Conditioner which uses gas or oil for heating.



Purchasing A New Air Conditioner

Purchasing a new cooling system for your home can be a nerve racking task. If it’s time to replace an aging or worn out air conditioner we are here to help make the process easier for you.

A cooling system is one of the biggest uses of energy in your home but it doesn’t have to be as costly. An air conditioner’s performance is measured by System Efficiency Ratio (SER™). SER™ is a relatively new standard in the air conditioning and heating industry. It’s an efficiency rating of your installed system, including the effects of the furnace, the ductwork and the construction of your home. To read more information about SER™ Click Here.

Replacing an existing working air conditioner

Before quoting to replace your existing air conditioner, as an NCI certified contractor we measure the SER™ of your system. The test reveals the ratio of actual cooling delivery compared to the rated amount the equipment produced when the manufacturer tested the equipment. For example, if an air conditioner worked perfectly, it would be rated at a CSER™ of 100%. But if it only delivered half the heating, the CSER would be 50%. In simple terms, a 14 Seasonal Energy Efficiency Ratio (SEER) air conditioner could only operate like 7 SEER equipment.

We test your equipment first to determine the problem with your system then we recommend the best solution for you.



Replacing a worn out or old air conditioner

Before replacing just the air conditioner we look at your house as a whole because your air conditioner is only one part that affects the SER™. We look at the furnace, the ductwork, and the construction of your home because if any one piece of your system isn’t up to top shape it can affect your SER™, your comfort, and can cost you money.

After analyzing your house and the system we will recommend the best solution for you. It is not uncommon to find the ductwork needs fixing or replacement, the furnace needs to be cleaned or other problems caused by your house. But when these problems are fixed and the right air conditioner installed you will notice the difference in your comfort and your energy bills.

We look at the whole picture to ensure that you receive the best possible comfort system.



Understanding Air Conditioning

Energy-Efficient Air Conditioning

Are you considering buying a new air conditioner? Or, are you dissatisfied with the operation of your current air conditioner? Are you unsure whether to fix or replace it? Are you concerned about high summer utility bills? If you answered yes to any of these questions, this publication can help. With it, you can learn about various types of air conditioning systems and how to maintain your air conditioner, hire professional air conditioning services, select a new air conditioner, and ensure that your new air conditioner is properly installed. Proper sizing, selection, installation, maintenance, and correct use are keys to cost-effective operation and lower overall costs.

A Technical Explanation of How a System Works

Air conditioners employ the same operating principles and basic components as your home refrigerator. An air conditioner cools your home with a cold indoor coil called the evaporator. The condenser, a hot outdoor coil, releases the collected heat outside. The evaporator and condenser coils are serpentine tubing surrounded by aluminum fins. This tubing is usually made of copper. A pump, called the compressor, moves a heat transfer fluid (or refrigerant) between the evaporator and the condenser. The pump forces the refrigerant through the circuit of tubing and fins in the coils. The liquid refrigerant evaporates in the indoor evaporator coil, pulling heat out of indoor air and thereby cooling the home. The hot refrigerant gas is pumped outdoors into the condenser where it reverts back to a liquid giving up its heat to the air-flowing over the condenser's metal tubing and fins.



Types of Air Conditioners

The basic types of air conditioners are room air conditioners, split-system central air conditioners, and packaged central air conditioners.

Room Air Conditioners

Room air conditioners cool rooms rather than the entire home. If they provide cooling only where they're needed, room air conditioners are less expensive to operate than central units, even though their efficiency is generally lower than that of central air conditioners.

Smaller room air conditioners (i.e., those drawing less than 7.5 amps of electricity) can be plugged into any 15- or 20-amp, 115-volt household circuit that is not shared with any other major appliances. Larger room air conditioners (i.e., those drawing more than 7.5 amps) need their own dedicated 115-volt circuit. The largest models require a dedicated 230-volt circuit.

Central Air Conditioners

Central air conditioners circulate cool air through a system of supply and return ducts. Supply ducts and registers (i.e., openings in the walls, floors, or ceilings covered by grills) carry cooled air from the air conditioner to the home. This cooled air becomes warmer as it circulates through the home; then it flows back to the central air conditioner through return ducts and registers. A central air conditioner is either a split-system unit or a packaged unit.

In a split-system central air conditioner, an outdoor metal cabinet contains the condenser and compressor, and an indoor cabinet contains the evaporator. In many split-system air conditioners, this indoor cabinet also contains a furnace or the indoor part of a heat pump. The air conditioner's evaporator coil is installed in the cabinet or main supply duct of this furnace or heat pump. If your home already has a furnace but no air conditioner, a split-system is the most economical central air conditioner to install.

In a packaged central air conditioner, the evaporator, condenser, and compressor are all located in one cabinet, which usually is placed on a roof or on a concrete slab next to the house's foundation. This type of air conditioner also is used in small commercial buildings. Air supply and return ducts come from indoors through the home's exterior wall or roof to connect with the packaged air conditioner, which is usually located outdoors. Packaged air conditioners often include electric heating coils or a natural gas furnace. This combination of air conditioner and central heater eliminates the need for a separate furnace indoors.

Evaporative Coolers

An evaporative cooler (also called a "swamp cooler") is a completely different type of air conditioner that works well in hot, dry climates.

These units cool outdoor air by evaporation and blow it inside the building, causing a cooling effect much like the process when evaporating perspiration cools your body on a hot (but not overly humid) day. When operating an evaporative cooler, windows are opened part way to allow warm indoor air to escape as it is replaced by cooled air.

Evaporative coolers cost about one-half as much to install as central air conditioners and use about one-quarter as much energy. However, they require more frequent maintenance than refrigerated air conditioners and they're suitable only for areas with low humidity.



Maintaining Existing Air Conditioners

Older air conditioners may still be able to offer years of relatively efficient use. However, making your older air conditioner last requires you to perform proper operation and maintenance.

Air Conditioning Problems

One of the most common air conditioning problems is improper operation. If your air conditioner is on, be sure to close your home's windows and outside doors. Other common problems with existing air conditioners result from faulty installation, poor service procedures, and inadequate maintenance. Improper installation of your air conditioner can result in leaky ducts and low airflow.

Many times, the refrigerant charge (the amount of refrigerant in the system) does not match the manufacturer's specifications. If proper refrigerant charging is not performed during installation, the performance and efficiency of the unit is impaired. Service technicians often fail to find refrigerant charging problems or even worsen existing problems by adding refrigerant to a system that is already full. Air conditioner manufacturers generally make rugged, high quality products. If your air conditioner fails, it is usually for one of the common reasons listed below:

Refrigerant Leaks

If your air conditioner is low on refrigerant, either it was undercharged at installation, or it leaks. If it leaks, simply adding refrigerant is not a solution. A trained technician should fix any leak, test the repair, and then charge the system with the correct amount of refrigerant. Remember that the performance and efficiency of your air conditioner is greatest when the refrigerant charge exactly matches the manufacturer's specification, and is neither undercharged nor overcharged.

Inadequate Maintenance

If you allow filters and air conditioning coils to become dirty, the air conditioner will not work properly, and the compressor or fans are likely to fail prematurely.

Electric Control Failure

The compressor and fan controls can wear out, especially when the air conditioner turns on and off frequently, as is common when a system is oversized. Because corrosion of wire and terminals is also a problem in many systems, electrical connections and contacts should be checked during a professional service call.

Needed Maintenance

An air conditioner's filters, coils, and fins require regular maintenance for the unit to function effectively and efficiently throughout its years of service. Neglecting necessary maintenance ensures a steady decline in air conditioning performance while energy use steadily increases.

Air Conditioner Filters

The most important maintenance task that will ensure the efficiency of your air conditioner is to routinely replace or clean its filters. Clogged, dirty filters block normal airflow and reduce a system's efficiency significantly. With normal airflow obstructed, air that bypasses the filter may carry dirt directly into the evaporator coil and impair the coil's heat-absorbing capacity. Filters are located somewhere along the return duct's length. Common filter locations are in walls, ceilings, furnaces, or in the air conditioner itself.

Some types of filters are reusable; others must be replaced. They are available in a variety of types and efficiencies. Clean or replace your air conditioning system's filter or filters every month or two during the cooling season. Filters may need more frequent attention if the air conditioner is in constant use, is subjected to dusty conditions, or you have fur-bearing pets in the house.

Air Conditioner Coils

The air conditioner's evaporator coil and condenser coil collect dirt over their months and years of service. A clean filter prevents the evaporator coil from soiling quickly. In time, however, the evaporator coil will still collect dirt. This dirt reduces air-flow and insulates the coil which reduces its ability to absorb heat. Therefore, your evaporator coil should be checked every year and cleaned as necessary.

Outdoor condenser coils can also become very dirty if the outdoor environment is dusty or if there is foliage nearby. You can easily see the condenser coil and notice if dirt is collecting on its fins.

You should minimize dirt and debris near the condenser unit. Your dryer vents, falling leaves, and lawn mower are all potential sources of dirt and debris. Cleaning the area around the coil, removing any debris, and trimming foliage back at least 2 feet allow for adequate airflow around the condenser.

Coil Fins

The aluminum fins on evaporator and condenser coils are easily bent and can block air-flow through the coil. Air conditioning wholesalers sell a tool called a "fin comb" that will comb these fins back into nearly original condition.

Sealing and Insulating Air Ducts

An enormous waste of energy occurs when cooled air escapes from supply ducts or when hot attic air leaks into return ducts. Recent studies indicate that 10% to 30% of the conditioned air in an average central air conditioning system escapes from the ducts.

For central air conditioning to be efficient, ducts must be airtight. Hiring a competent professional service technician to detect and correct duct leaks is a good investment, since leaky ducts may be difficult to find without experience and test equipment. Ducts must be sealed with duct "mastic." The old standby of duct tape is many times ineffective for sealing ducts.

Obstructions can impair the efficiency of a duct system almost as much as leaks. You should be careful not to obstruct the flow of air from supply or return registers with furniture, drapes, or tightly fitted interior doors. Dirty filters and clogged evaporator coils can also be major obstructions to airflow.

The large temperature difference between attics and ducts makes heat conduction through ducts almost as big a problem as air leakage and obstructions. Ducts in attics should be insulated heavily in addition to being made airtight.



Buying a New Air Conditioner for Your Home

Today's best air conditioners use 30% to 50% less energy to produce the same amount of cooling as air conditioners made in the mid 1970s. Even if your air conditioner is only 10 years old, you may save 20% to 40% of your cooling energy costs by replacing it with a newer, more efficient model.

Sizing your Air Conditioners

Air conditioners are rated by the number of British Thermal Units (Btu) of heat they can remove per hour. Another common rating term for air conditioning size is the "ton," which is 12,000 Btu per hour.

How Big should your Air Conditioner Be?

The size of an air conditioner depends on:

  1. how large your home is and how many windows it has;
  2. how much shade is on your home's windows, walls, and roof;
  3. how much insulation is in your home's ceiling and walls;
  4. how much air leaks into your home from the outside; and
  5. how much heat the occupants and appliances in your home generate.

An air conditioner's efficiency, performance, durability, and initial cost depend on matching its size to the above factors.

Make sure you buy the correct size of air conditioner. Two groups—the Air Conditioning Contractors of America (ACCA) and the American Society of Heating, Refrigerating, and Air Conditioning Engineers (ASHRAE)—publish calculation procedures for sizing central air conditioners. Reputable air conditioning contractors will use one of these procedures, often performed with the aid of a computer, to size your new central air conditioner.

Be aware that a large air conditioner will not provide the best cooling. Buying an oversized air conditioner penalizes you in the following ways.

It costs more to buy a larger air conditioner than you need. The larger-than-necessary air conditioner cycles on and off more frequently, reducing its efficiency. Frequent cycling makes indoor temperatures fluctuate more and results in a less comfortable environment. Frequent cycling also inhibits moisture removal. In humid climates, removing moisture is essential for acceptable comfort. In addition, this cycling wears out the compressor and electrical parts more rapidly. A larger air conditioner uses more electricity and creates added demands on electrical generation and delivery systems.



Air Conditioner Efficiency

Each air conditioner has an energy-efficiency rating that lists how many Btu per hour are removed for each watt of power it draws. For room air conditioners, this efficiency rating is the Energy Efficiency Ratio, or EER. For central air conditioners, it is the Seasonal Energy Efficiency Ratio, or SEER. These ratings are posted on an Energy Guide Label, which must be conspicuously attached to all new air conditioners. Many air conditioner manufacturers are participants in the voluntary EnergyStar® labeling program (see Source List in this publication). EnergyStar®-labeled appliances mean that they have high EER and SEER ratings.

In general, new air conditioners with higher EERs or SEERs sport higher price tags. However, the higher initial cost of an energy-efficient model will be repaid to you several times during its life span. Your utility company may encourage the purchase of a more efficient air conditioner by rebating some or all of the price difference. Buy the most efficient air conditioner you can afford, especially if you use (or think you will use) an air conditioner frequently and/or if your electricity rates are high.

Room Air Conditioners—EER-

Room air conditioners generally range from 5,500 Btu per hour to 14,000 Btu per hour. National appliance standards require room air conditioners built after January 1, 1990, to have an EER of 8.0 or greater. Select a room air conditioner with an EER of at least 9.0 if you live in a mild climate. If you live in a hot climate, select one with an EER over 10.

The Association of Home Appliance Manufacturers reports that the average EER of room air conditioners rose 47% from 1972 to 1991. If you own a 1970s-vintage room air conditioner with an EER of 5 and you replace it with a new one with an EER of 10, you will cut your air conditioning energy costs in half.

Central Air Conditioners—SEER-

National minimum standards for central air conditioners require a SEER of 9.7 and 13.0, for single-package and split-systems, respectively. But you do not need to settle for the minimum standard—there is a wide selection of units with SEERs of 18.

Before 1979, the SEERs of central air conditioners ranged from 4.5 to 8.0. Replacing a 1970s-era central air conditioner with a SEER of 6 with a new unit having a SEER of 13 will cut your air conditioning costs more than in half.

Sound Considerations

The Sound level of the out door section may be important to you do to the units location, or proximity to your neighbor's window. Most units today have sound ratings that are measured in decibel ratings.



What to Look for in Professional Service

When your air conditioner needs more than the regular maintenance described previously, hire a professional service technician. A well-trained technician will find and fix problems in your air conditioning system. However, not all service technicians are competent. Incompetent service technicians forsake proper diagnosis and perform only minimal stop-gap measures.

Insist that the Technician:

  1. check for correct amount of refrigerant;
  2. test for refrigerant leaks using a leak detector;
  3. capture any refrigerant that must be evacuated from the system, instead of illegally releasing it to the atmosphere;
  4. check for and seal duct leakage in any part of your system that runs in the attic, crawl, or garage
  5. measure air-flow through the evaporator coil;
  6. verify the correct electric control sequence and make sure that the heating system and cooling system cannot operate simultaneously;
  7. inspect electric terminals, clean and tighten connections, and apply a non-conductive coating if necessary;
  8. oil motors and check belts for tightness and wear;
  9. check the accuracy of the thermostat.

How to Choose a Contractor

Choosing a contractor may be the most important and difficult task in buying a new central air conditioning system. Ask prospective contractors for recent references. If you are replacing your central air conditioner, tell your contractor what you liked and did not like about the old system. If the system failed, ask the contractor to find out why. The best time to fix existing problems is when a new system is being installed.

When designing your new air conditioning system, the contractor you choose should:

  1. use a written calculation procedure or computer program to size the air conditioner;
  2. provide a written contract listing the main points of your installation that includes the results of the cooling load calculation;
  3. give you a written warranty on equipment and workmanship.

Avoid making your decision solely on the basis of price. The quality of the installation should be your highest priority, because quality will determine energy cost, comfort, and durability.



Installation and Location of Air Conditioners

If your air conditioner is installed correctly, or if major installation problems are found and fixed, it will perform efficiently for years with only minor routine maintenance. However, many air conditioners are not installed correctly. As an unfortunate result, modern energy-efficient air conditioners can perform almost as poorly as older inefficient models.

Be sure that your contractor performs the following procedures when installing a new central air conditioning system:

  1. allows adequate indoor space for the installation, maintenance, and repair of the new system, and installs an access door in the furnace or duct to provide a way to clean the evaporator coil.
  2. uses a duct-sizing methodology such as the Air Conditioning Contractors of America (ACCA) Manual D.
  3. ensures there are enough supply registers to deliver cool air and enough return air registers to carry warm house air back to the air conditioner.
  4. installs duct work within the conditioned space, not in the attic, wherever possible – insulating it where it must be run outside the treated structure.
  5. seals all ducts with duct mastic and heavily insulates attic ducts.
  6. locates the condensing unit where its noise will not keep you or your neighbors awake at night, if possible.
  7. places the condensing unit in a shady spot, if possible, which can reduce your air conditioning costs by 1% to 2%.
  8. verifies that the newly installed air conditioner has the exact refrigerant charge and air-flow rate specified by the manufacturer.
  9. locates the thermostat away from heat sources, such as windows, or supply registers.

If you are replacing an older or failed split system, be sure that the evaporator coil is replaced with a new one that exactly matches the condenser coil in the new condensing unit. (The air conditioner's efficiency will likely not improve if the existing evaporator coil is left in place; in fact, the old coil could cause the new compressor to fail prematurely.)

If you install a new room air conditioner, try to:

  1. locate the air conditioner in a window or wall area near the center of the room and on the shadiest side of the house.
  2. minimize air leakage by fitting the room air conditioner snugly into its opening and sealing gaps with a foam weather stripping material.

Paying attention to your air conditioning system saves you money and reduces environmental pollution. Notice whether your existing system is running properly, and maintain it regularly. Or, if you need to purchase a new air conditioner, be sure it is sized and installed correctly and has a good EER or SEER rating.

Using Your Air Conditioner

Unless, your contractor has sized your air conditioner to maximize humidity control instead of just cooling the air temperature, an air conditioner will cool the air in your home fairly quickly. For economical operation, turn it on only when your home is occupied. You may consider installing a programmable thermostat. These allow you to set the time when the air conditioner will turn on before you arrive home from work on a hot day. Contact EREC (see Source List) for the fact sheet Automatic and Programmable Thermostats. During the day, keep the drapes or blinds closed on windows that face east, south, and west. This will help reduce solar heat gain into your home.



Source List

There are many groups offering information on air conditioning. The following groups are just a few that can assist you in increasing your air conditioning efficiency. Some of these organizations provide only materials appropriate for professionals in the air conditioning industry.

  • Air Conditioning and Refrigeration Institute (ARI) 4301 N. Fairfax Drive, Suite 425 Arlington, VA 22203 (703) 524-8800 Fax: (703) 528-3816 www.ari.org ARI represents manufacturers of air conditioning, refrigeration, and heating equipment and has consumer brochures on a variety of topics.
  • American Society of Heating, Refrigeration, and Air Conditioning Engineers (ASHRAE) 1791 Tullie Circle, N.E. Atlanta, GA 30329 (404) 636-8400 Fax: (404) 321-5478 www.ashrae.org ASHRAE is organized solely for the purpose of advancing the arts and science of heating, ventilation, air conditioning, and refrigeration for the public's benefit through research, standards writing, continuing education, and publications.
  • Air Conditioning Contractors of America (ACCA) 1513 16th Street NW Washington, DC 20036 (202) 483-9370 Fax: (202) 234-4721 www.acca.org The Air Conditioning Contractors of America is the most active and widely recognized organization representing contractors in the heating, ventilation, air conditioning, and refrigeration (HVACR) industry.
  • EnergyStar® Program 1-888-STAR-YES e-mail: info@energystar.gov www.energystar.gov ENERGY STAR®-labeled products, including heating and cooling equipment, use less energy than other products and save you money on utility bills. These products are made by all major manufacturers and are available at stores everywhere.
  • Florida Solar Energy Center (FSEC) 1679 Clear Lake Road Cocoa, FL 32922 (407) 638-1000 Fax: (407) 638-1010 www.fsec.ucf.edu FSEC provides information on building in hot, humid climates.

For more information about cooling and air conditioning, as well as on a wealth of other energy-efficiency topics, contact:

  • The Energy Efficiency and Renewable Energy Clearinghouse (EREC) P.O. Box 3048 Merrifield, VA 22116 (800) 363-3732 (800-DOE-EREC) Fax: (703) 893-0400 E-mail: doe.erec@nciinc.com www.eren.doe.gov/consumerinfo EREC provides free general and technical information to the public on many topics and technologies pertaining to energy efficiency and renewable energy.

Reading List

The following publications provide more information on air conditioning. The list does not cover all the available books, reports, and articles on air conditioning, nor is the mention of any publication a recommendation or endorsement.

  • ASHRAE Journal, American Society of Heating, Refrigerating and Air Conditioning Engineers (ASHRAE), 1791 Tullie Circle N.E., Atlanta, GA 30329-2305, monthly trade magazine.
  • "Consumer Guide to Home Energy Savings", A. Wilson and J. Morrill, American Council for an Energy-Efficient Economy, 1001 Connecticut Ave. NW, Suite 801, Washington, DC 20036, 1998.
  • Home Energy, The Magazine of Residential Energy Conservation, 2124 Kitteredge, #95, Berkeley, CA 94704, monthly trade magazine. For example, the May/June 1995 issue had an article about properly sizing air conditioning systems.
  • Consumer Reports, The Consumers Union of the United States, Inc., 101 Truman Avenue, Yonkers, NY 10703, (800) 234-1645 (subscriptions and back issues). "Chill Out: A Guide to Air Conditioning," (63:6) pp. 36-42, June 1998. "Cool It (Room/Window Air Conditioners)" (64:6) pp. 35-37, June 1999.

This document was produced for the U.S. Department of Energy (DOE) by the National Renewable Energy Laboratory (NREL), a DOE national laboratory. The document was produced by the Information Services Program, under the DOE Office of Energy Efficiency and Renewable Energy. The Energy Efficiency and Renewable Energy Clearinghouse (EREC) is operated by NCI Information Systems, Inc., for NREL / DOE. The statements contained herein are based on information known to EREC and NREL at the time of printing. No recommendation or endorsement of any product or service is implied if mentioned by EREC.

We Accept